News:
Buy "The Book" on Q-jets and OverDrive Transmission Swaps. On the Website Home Page!
Subject / Started by  |
Replies / Views | Last post | ||
|---|---|---|---|---|
|
|
0 Replies
2175 Views |
May 26, 2021, 01:14:01 PMby Glutenfreecarbs |
|
|
|
|
Cadillac Q-jet 7040230
Started by Glutenfreecarbs |
0 Replies
2340 Views |
May 07, 2021, 10:45:55 AM by Glutenfreecarbs |
|
|
14 Replies
9869 Views |
July 18, 2021, 05:30:07 AM by Cliff Ruggles |
|
|
|
|
14 Replies
6658 Views |
July 10, 2021, 09:41:36 AM by blazer74 |
|
|
|
|
Can the EGR port be used for dist vacuum?
Started by gkz |
1 Replies
2779 Views |
May 25, 2012, 04:28:16 AM by Cliff Ruggles |
|
|
|
Thanks for...
Started by gkz |
1 Replies
2660 Views |
May 25, 2012, 04:26:30 AM by Cliff Ruggles |
|
|
|
Is this a good carb choice?
Started by gixxer711 |
4 Replies
3867 Views |
December 06, 2016, 11:56:31 AM by gixxer711 |
|
|
|
Carburetor settings
Started by Gio_84 |
4 Replies
3254 Views |
October 05, 2021, 11:49:57 PM by Gio_84 |
|
|
|
Is the front vent supposed to be empty?
Started by geebjen |
2 Replies
2069 Views |
January 24, 2025, 12:00:58 PM by geebjen |
|
|
|
3 Replies
4324 Views |
November 05, 2010, 09:14:08 AM by geberhard |
|
|
|
|
Power Piston Assy Hanger spring
Started by Gearheadzs |
4 Replies
3178 Views |
January 04, 2013, 10:07:55 AM by Shark Racer |
|
|
|
straightening a bent casting
Started by Gator67 |
1 Replies
3109 Views |
August 26, 2012, 04:34:05 PM by Cliff Ruggles |
|
|
|
New guy, Cadillac Q-Jet questions...
Started by Gator |
1 Replies
3660 Views |
July 27, 2012, 03:02:22 AM by Cliff Ruggles |
|
|
|
starting fresh
Started by gassman_67 |
3 Replies
3063 Views |
February 09, 2016, 02:44:13 AM by Frank400 |
|
|
|
frankenstein q-jet wont idle
Started by GASGTO73 |
3 Replies
3699 Views |
June 24, 2013, 06:12:51 PM by GASGTO73 |
|
|
|
PCV to the REAR, OK?
Started by garybohannon |
1 Replies
3510 Views |
April 17, 2011, 11:24:27 AM by Schurkey |
|
|
|
7044232 Caddy to GM350
Started by Fuzzy One |
4 Replies
2713 Views |
February 13, 2019, 02:42:28 AM by Cliff Ruggles |
|
|
|
A/N fitting into fuel inlet nut?
Started by fussfeld |
5 Replies
3932 Views |
January 12, 2016, 04:11:25 AM by fussfeld |
|
|
|
Idle wells fill with bowl?
Started by fussfeld |
3 Replies
3129 Views |
July 18, 2021, 03:38:04 PM by fussfeld |
|
|
|
Throttle plate position at curb idle:
Started by fussfeld |
1 Replies
2441 Views |
June 26, 2021, 03:09:03 PM by Cliff Ruggles |
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll