News:
We buy American, and use American Made parts for all of our exclusive Cliff's Carburetor parts and kits.
Subject / Started by  |
Replies / Views | Last post | ||
|---|---|---|---|---|
|
|
Hot Air choke
Started by Paul |
0 Replies
3947 Views |
April 26, 2011, 09:26:33 AMby Paul |
|
|
|
8 Replies
6446 Views |
December 06, 2010, 08:21:40 AM by pauliq |
|
|
|
|
7 Replies
3475 Views |
January 24, 2025, 12:52:40 PM by GSP7 |
|
|
|
|
High altitude carb at low altitude
Started by Pav8427 |
1 Replies
2728 Views |
September 22, 2015, 02:42:34 AM by Cliff Ruggles |
|
|
|
5 Replies
4673 Views |
January 26, 2021, 12:34:11 PM by Pav8427 |
|
|
|
|
Base setting for throttle angle
Started by Pav8427 |
9 Replies
3974 Views |
March 05, 2018, 04:33:58 PM by Frank400 |
|
|
Adjustable idle air
Started by Pav8427 |
10 Replies
4456 Views |
March 03, 2018, 03:28:57 AM by Pav8427 |
|
|
|
Emission crud
Started by Pav8427 |
6 Replies
3246 Views |
September 03, 2019, 10:13:13 AM by Pav8427 |
|
|
|
BIG Delco book owners ???
Started by Pav8427 |
3 Replies
3095 Views |
October 22, 2020, 10:24:35 AM by Pav8427 |
|
|
|
2 Replies
2623 Views |
August 21, 2020, 07:03:07 AM by Pav8427 |
|
|
|
|
Modifying secondary metering rods
Started by Pav8427 |
5 Replies
1494 Views |
October 10, 2025, 12:47:59 PM by Cadman-iac |
|
|
|
Early non APT primary rod set up.
Started by Pav8427 |
8 Replies
2650 Views |
June 06, 2025, 12:02:50 AM by Cliff Ruggles |
|
|
|
Tips and Tricks that Work. No BS.
Started by Pav8427 |
2 Replies
2535 Views |
May 05, 2023, 01:58:55 PM by Pav8427 |
|
|
|
Another 'book' in the works?????
Started by Pav8427 |
1 Replies
2688 Views |
April 23, 2020, 03:59:45 AM by Cliff Ruggles |
|
|
|
Quick quiz on plating parts.
Started by Pav8427 |
1 Replies
2254 Views |
December 15, 2022, 05:45:01 AM by Cliff Ruggles |
|
|
|
NOS carb parts
Started by Pav8427 |
3 Replies
2682 Views |
March 10, 2018, 06:26:00 PM by Ethan1 |
|
|
|
67 Pontiac intake
Started by Pav8427 |
0 Replies
2037 Views |
July 17, 2018, 07:35:39 AM by Pav8427 |
|
|
|
Virgin 17059553
Started by Pav8427 |
10 Replies
4621 Views |
March 27, 2020, 02:18:18 AM by Cliff Ruggles |
|
|
|
Un-warping jig
Started by Pav8427 |
6 Replies
3725 Views |
March 03, 2018, 03:11:41 AM by Pav8427 |
|
|
|
E4ME measurements any thoughts?
Started by Peer81 |
4 Replies
4054 Views |
June 08, 2011, 09:37:22 AM by Peer81 |
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll