News:
We buy American, and use American Made parts for all of our exclusive Cliff's Carburetor parts and kits.
| Subject / Started by | Replies  / Views |
Last post | ||
|---|---|---|---|---|
|
|
idle tubes
Started by Paul |
1 Replies
3553 Views |
March 15, 2011, 04:14:07 AMby Cliff Ruggles |
|
|
|
1 Replies
3380 Views |
March 15, 2011, 04:13:08 AM by Cliff Ruggles |
|
|
|
|
Gas in Vac Port
Started by JMac11 |
1 Replies
3128 Views |
November 04, 2011, 05:40:49 AM by Cliff Ruggles |
|
|
|
1 Replies
3185 Views |
June 05, 2012, 03:09:27 AM by Cliff Ruggles |
|
|
|
|
which qjet?
Started by turbo210 |
1 Replies
3272 Views |
October 31, 2013, 03:52:11 AM by Cliff Ruggles |
|
|
|
Secondary Well Pull Over Orifices
Started by Gmoney |
1 Replies
2650 Views |
September 10, 2013, 05:26:18 AM by Cliff Ruggles |
|
|
|
1 Replies
3355 Views |
December 06, 2011, 03:23:16 AM by Cliff Ruggles |
|
|
|
|
brass tubes in top plate ?
Started by bober |
1 Replies
2823 Views |
July 29, 2013, 10:18:06 AM by Ethan1 |
|
|
|
Marine carb on vehicle
Started by Vince57 |
1 Replies
2905 Views |
December 04, 2013, 04:44:15 AM by Cliff Ruggles |
|
|
|
1 Replies
2994 Views |
March 31, 2013, 03:10:27 AM by Cliff Ruggles |
|
|
|
|
Unusual Secondary Jet Repair
Started by levyb |
1 Replies
2749 Views |
May 29, 2012, 04:17:04 AM by Cliff Ruggles |
|
|
|
Can the EGR port be used for dist vacuum?
Started by gkz |
1 Replies
2897 Views |
May 25, 2012, 04:28:16 AM by Cliff Ruggles |
|
|
|
linkage and spring
Started by petes70 |
1 Replies
3272 Views |
February 22, 2011, 03:36:06 AM by Cliff Ruggles |
|
|
|
Primary POE 7040263
Started by Grych |
1 Replies
3439 Views |
June 09, 2011, 01:33:34 AM by Cliff Ruggles |
|
|
|
Ccc help
Started by Breakneck88 |
1 Replies
3682 Views |
June 21, 2013, 04:05:25 AM by Cliff Ruggles |
|
|
|
secondary air flap shaft looseness
Started by sticknstring |
1 Replies
3583 Views |
February 10, 2011, 03:49:26 AM by Cliff Ruggles |
|
|
|
Carburetor help
Started by Joah_from_Alberta |
1 Replies
2600 Views |
June 07, 2013, 03:17:04 AM by Cliff Ruggles |
|
|
|
1 Replies
3029 Views |
June 01, 2012, 06:29:39 AM by Cliff Ruggles |
|
|
|
|
Use little clip on end of needle?
Started by daveo76 |
1 Replies
3011 Views |
May 19, 2012, 11:21:34 PM by daveo76 |
|
|
|
1 Replies
3529 Views |
January 28, 2011, 04:40:44 AM by Cliff Ruggles |
|
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll