News:
We buy American, and use American Made parts for all of our exclusive Cliff's Carburetor parts and kits.
| Subject / Started by | Replies  / Views |
Last post | ||
|---|---|---|---|---|
|
|
Thanks Cliff
Started by blockhead |
1 Replies
2730 Views |
October 19, 2010, 03:52:05 AMby Cliff Ruggles |
|
|
|
Power Piston
Started by Paul |
1 Replies
3188 Views |
March 26, 2011, 03:29:19 AM by Cliff Ruggles |
|
|
|
STAGGERED JETTING
Started by qjetsrule |
1 Replies
2777 Views |
May 17, 2012, 03:27:28 PM by TommyK |
|
|
|
Quadrajet 4MV 1968 Camaro
Started by CaliChevyV8 |
1 Replies
2803 Views |
December 03, 2011, 07:30:58 AM by Cliff Ruggles |
|
|
|
Baseplate Idle Mixture Holes
Started by Rhett |
1 Replies
2467 Views |
May 15, 2012, 02:21:03 PM by Rhett |
|
|
|
Use little clip on end of needle?
Started by daveo76 |
1 Replies
2371 Views |
May 19, 2012, 11:21:34 PM by daveo76 |
|
|
|
Is clip mandatory on needle ?
Started by Frank400 |
1 Replies
2852 Views |
May 04, 2012, 04:14:23 AM by Cliff Ruggles |
|
|
|
Gas in Vac Port
Started by JMac11 |
1 Replies
2509 Views |
November 04, 2011, 05:40:49 AM by Cliff Ruggles |
|
|
|
1 Replies
2548 Views |
April 12, 2011, 04:03:33 AM by Cliff Ruggles |
|
|
|
|
carb number 17084226
Started by bigblockman |
1 Replies
3474 Views |
April 30, 2012, 02:26:19 AM by Cliff Ruggles |
|
|
|
PCV to the REAR, OK?
Started by garybohannon |
1 Replies
3012 Views |
April 17, 2011, 11:24:27 AM by Schurkey |
|
|
|
Nozzle drip
Started by Paul |
1 Replies
3417 Views |
April 04, 2011, 04:49:00 PM by Cliff Ruggles |
|
|
|
stainless carb gasket
Started by Michael9040 |
1 Replies
2732 Views |
August 05, 2010, 04:23:04 AM by Cliff Ruggles |
|
|
|
Fuel ratio & float level
Started by 77cruiser |
1 Replies
2926 Views |
May 13, 2010, 05:15:03 AM by Cliff Ruggles |
|
|
|
ULTRASONIC CLEANERS
Started by billy 2 |
1 Replies
3057 Views |
May 09, 2010, 03:58:09 AM by Cliff Ruggles |
|
|
|
Removing Primary Shaft Screws
Started by von |
1 Replies
2815 Views |
May 08, 2010, 05:05:19 AM by billy 2 |
|
|
|
idle tubes
Started by 73ss |
1 Replies
2458 Views |
March 31, 2012, 04:16:14 AM by Cliff Ruggles |
|
|
|
1 Replies
2768 Views |
February 10, 2012, 04:55:23 AM by Cliff Ruggles |
|
|
|
|
Just wanted to share...
Started by Marx3 |
1 Replies
2966 Views |
April 24, 2010, 12:53:05 PM by Cliff Ruggles |
|
|
|
Original factory jets and rods
Started by mwoolston |
1 Replies
2834 Views |
January 15, 2012, 04:33:52 AM by Cliff Ruggles |
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll