News:
We buy American, and use American Made parts for all of our exclusive Cliff's Carburetor parts and kits.
| Subject / Started by | Replies / Views | Last post  |
||
|---|---|---|---|---|
|
|
5 Replies
4266 Views |
October 15, 2015, 05:57:16 AMby Cliff Ruggles |
|
|
|
|
Quadrajet 17085226
Started by lakedrifter |
5 Replies
4606 Views |
October 01, 2015, 11:43:37 AM by lakedrifter |
|
|
|
torqu setting for Q-jet
Started by trans am greg |
5 Replies
2872 Views |
September 30, 2015, 04:58:55 AM by trans am greg |
|
|
|
1 Replies
1828 Views |
September 24, 2015, 03:20:13 AM by Cliff Ruggles |
|
|
|
|
High altitude carb at low altitude
Started by Pav8427 |
1 Replies
1907 Views |
September 22, 2015, 02:42:34 AM by Cliff Ruggles |
|
|
Performance improvement
Started by Big Blue |
10 Replies
4553 Views |
September 22, 2015, 02:40:08 AM by Cliff Ruggles |
|
|
|
Tip-in procedure universal?
Started by Marx3 |
3 Replies
2639 Views |
September 12, 2015, 03:43:41 AM by Cliff Ruggles |
|
|
|
Question on needle and seat size
Started by Frank400 |
2 Replies
1926 Views |
September 10, 2015, 06:14:37 PM by Frank400 |
|
|
|
braided hose between pump and carb
Started by Frank400 |
3 Replies
2526 Views |
August 31, 2015, 07:22:21 AM by Ethan1 |
|
|
|
Calibration of 800cfm unit for mild 350 Chevy
Started by anvilhandsmagillacutty « 1 2 » |
16 Replies
7828 Views |
August 22, 2015, 05:41:49 AM by Cliff Ruggles |
|
|
|
5 Replies
3496 Views |
August 22, 2015, 04:30:46 AM by Cliff Ruggles |
|
|
|
Best carb set up?
Started by Bill1979 |
2 Replies
2183 Views |
August 20, 2015, 03:11:34 AM by Frank400 |
|
|
|
7028362 or 17057274
Started by knucklehead12 |
8 Replies
3690 Views |
August 14, 2015, 02:34:35 AM by von |
|
|
|
Air bleed thread size
Started by Marx3 |
13 Replies
4773 Views |
August 04, 2015, 12:52:19 AM by Marx3 |
|
|
|
7 Replies
3562 Views |
August 01, 2015, 10:35:28 AM by 85k10 |
|
|
|
|
17084285 or 17080204
Started by Avanwest |
0 Replies
1981 Views |
July 31, 2015, 09:27:58 AM by Avanwest |
|
|
|
17058531 opinions?
Started by sleddogg |
3 Replies
2316 Views |
July 30, 2015, 08:44:01 AM by sleddogg |
|
|
|
Jets and rods after engine rebuild
Started by eightballz |
11 Replies
5151 Views |
July 28, 2015, 07:27:19 AM by Cliff Ruggles |
|
|
|
Re Tapping idle mix holes
Started by 77cruiser |
1 Replies
1931 Views |
July 25, 2015, 01:30:16 PM by Ethan1 |
|
|
|
pcv hose connection
Started by bober |
2 Replies
2044 Views |
July 17, 2015, 03:18:46 PM by bober |
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll