News:
We buy American, and use American Made parts for all of our exclusive Cliff's Carburetor parts and kits.
| Subject / Started by | Replies / Views  |
Last post | ||
|---|---|---|---|---|
|
|
Conversion of a Q-Jet
Started by bigvette1 |
1 Replies
4875 Views |
February 23, 2009, 04:52:17 AMby Cliff Ruggles |
|
|
|
broken primary shaft butterfly screws
Started by FNG |
6 Replies
4888 Views |
October 23, 2013, 03:24:41 AM by Cliff Ruggles |
|
|
|
Black Smoke on deceleration
Started by boondocker |
9 Replies
4901 Views |
June 05, 2012, 03:52:12 AM by Cliff Ruggles |
|
|
|
Q-jet flooding under load
Started by rwberinger4x4 |
7 Replies
4907 Views |
July 16, 2015, 06:53:55 PM by rwberinger4x4 |
|
|
|
Cold start issue
Started by vickleford |
9 Replies
4913 Views |
November 25, 2014, 04:34:22 AM by Cliff Ruggles |
|
|
|
3 Replies
4919 Views |
August 14, 2009, 09:39:01 PM by 17058263 |
|
|
|
|
dirt track carb problem
Started by glntom |
5 Replies
4925 Views |
November 11, 2010, 06:20:18 PM by Toronado |
|
|
|
Need Help with Idle Tubes
Started by bigfoot |
6 Replies
4935 Views |
February 09, 2010, 06:09:25 PM by Cliff Ruggles |
|
|
marine quadrajet idles not smooth
Started by beaug |
13 Replies
4943 Views |
September 07, 2017, 04:34:19 AM by Cliff Ruggles |
|
|
|
replacing bushings
Started by FORREST MILLER |
1 Replies
4945 Views |
October 21, 2008, 04:29:23 AM by Cliff Ruggles |
|
|
|
Quadrajet causing ignition timing problems?
Started by jeffb |
4 Replies
4949 Views |
August 31, 2011, 07:24:28 AM by Cliff Ruggles |
|
|
|
15 Replies
4972 Views |
January 11, 2018, 12:33:53 PM by Hillbillyenginering |
|
|
|
|
5 Replies
4979 Views |
April 18, 2024, 07:05:56 AM by Mechanic No. 4 |
|
|
|
|
Quadrajet bogging at WOT
Started by knucklehead12 |
3 Replies
4979 Views |
February 09, 2015, 05:42:48 PM by knucklehead12 |
|
|
|
engine goes extremely lean off idle
Started by matt69olds |
7 Replies
4986 Views |
January 19, 2016, 03:52:28 AM by Cliff Ruggles |
|
|
|
Sudden onset of Hard Starting
Started by ditchdr |
4 Replies
4989 Views |
June 01, 2009, 02:32:40 AM by Cliff Ruggles |
|
|
|
6 Replies
5002 Views |
December 18, 2014, 05:50:41 AM by Cliff Ruggles |
|
|
|
|
11 Replies
5011 Views |
July 29, 2013, 08:24:17 AM by Shark Racer |
|
|
|
|
Nozzle drip on ported vac
Started by blazer74 |
9 Replies
5037 Views |
August 04, 2013, 11:01:27 PM by blazer74 |
|
|
|
Plastic or brass float?
Started by Toronado |
3 Replies
5089 Views |
April 02, 2011, 01:37:53 AM by Toronado |
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll