News:
We buy American, and use American Made parts for all of our exclusive Cliff's Carburetor parts and kits.
Subject / Started by  |
Replies / Views | Last post | ||
|---|---|---|---|---|
|
|
4.3L Mercruiser QJ
Started by Baylinerchuck |
8 Replies
4719 Views |
September 15, 2020, 02:57:21 AMby Cliff Ruggles |
|
|
|
Needle & Seat selection
Started by baxternick |
3 Replies
3972 Views |
October 14, 2016, 03:38:50 AM by Cliff Ruggles |
|
|
|
2 Replies
3114 Views |
November 30, 2016, 05:38:28 AM by Cliff Ruggles |
|
|
|
Chasing lean condition at WOT
Started by baxternick |
13 Replies
8589 Views |
October 16, 2016, 02:21:55 AM by Marx3 |
|
|
|
6 Replies
4791 Views |
April 21, 2016, 09:29:46 PM by 429bbf |
|
|
|
|
Idle speed changes daily...
Started by baxternick |
2 Replies
4408 Views |
May 31, 2017, 02:26:52 AM by Cliff Ruggles |
|
|
|
17 Replies
13505 Views |
February 26, 2009, 08:35:12 AM by Cliff Ruggles |
|
|
|
|
17082403 Marine: idle circuit problem
Started by BarryK3 |
7 Replies
4594 Views |
May 14, 2020, 01:10:06 AM by Kenth |
|
|
|
17 Replies
7385 Views |
February 22, 2020, 08:16:33 PM by BarryK3 |
|
|
|
|
Fuel pressure issue? Comes and Go's
Started by BARRACUDA1968 |
9 Replies
4809 Views |
April 25, 2014, 02:39:24 AM by von |
|
|
|
Stumble Right After Car Grabs 2nd Gear
Started by BanditRich |
8 Replies
4144 Views |
October 10, 2019, 06:55:23 AM by BanditRich |
|
|
Bog From Dead Stop
Started by BanditRich « 1 2 » |
26 Replies
13179 Views |
September 10, 2019, 05:20:28 AM by Cliff Ruggles |
|
|
|
Won't hold WOT
Started by azathoth |
5 Replies
4354 Views |
November 09, 2013, 05:57:04 PM by blazer74 |
|
|
|
Tuning a Edelbrock 1910 for Buick 455
Started by avmechanic |
3 Replies
3963 Views |
July 23, 2020, 03:18:41 AM by Cliff Ruggles |
|
|
|
Leaning out during braking/deceleration
Started by autonaut |
1 Replies
2887 Views |
August 09, 2014, 06:50:59 AM by autonaut |
|
|
|
7040273 Carb poor idle
Started by ArlingtonJudge |
8 Replies
4808 Views |
August 03, 2025, 10:32:39 AM by ArlingtonJudge |
|
|
|
3 Replies
3567 Views |
May 14, 2014, 11:10:41 AM by Marx3 |
|
|
|
|
How to set air & lean screws
Started by alrobjr |
1 Replies
3985 Views |
March 30, 2012, 12:19:26 PM by Schurkey |
|
|
|
Idle Mixture screws
Started by AK_quad |
5 Replies
4280 Views |
August 24, 2012, 05:16:08 AM by Cliff Ruggles |
|
|
|
Wrong length primary metering rods?
Started by akdale |
4 Replies
5179 Views |
July 06, 2012, 07:47:04 AM by akdale |
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll