Quadrajet Problem Solving > Dialing in your rebuilt Quadrajet carburetor
Set up tweaks for extremely mild small block chevy
dphipps:
I had been trying to figure out a off idle stumble off and on for some time. It was never much concern but I decided to dig into a bit the other day. I found that with the accelerator pump disabled the problem went away, so I figured it's running rich.
So off the carb came and I noticed it was wet on the bottom so I re checked the well plugs and sure enough the primary ones leak so I have repaired that and will be re assembling the carb this week. I did check this when I originally rebuilt it but the bubbles were so small that I probably just didn't observe close enough in the beginning. I feel this leak was causing a lot of the problem? I imagine once it gets warm and has vacuum on it the leak is bigger than It seems?
So I figure while it's off I'd see if there's any tweaks I can make while its apart. I have piles of scrap carbs and parts so I do have a pretty good selection of jets/rods/hangers, but I am a complete novice as far as tuning goes.
I hadn't used the carb before rebuilding it so I'm not sure how it functioned prior to rebuilt. The carb was rebuilt around 2 years ago with a kit from Cliff's, this stumble problem was there from the start. No modifications were made to the carb and I put bushings in the baseplate.
Specs:
-1979 halfton, 350SBC with stock heads and an edelbrock intake
- performer cam (Intake duration: 204 Degrees • Exhaust duration: 214 Degrees • Intake lift: .420” • Exhaust lift: .442” • Lobe separation: 112 Degree • Intake Center Line: 107 Degree )
- 3.08 gears, TH350 and stock converter with a shift kit
- 14* inital timing and somewhere around 36* total (haven't checked again after some more fiddling)
- headers with 2.5" dual exhaust
Carb:
- 17084285
- 43K primary rod
- 73 jets
- CH secondary rod
- K hanger
As you can see it's not a hot rod but it might as well run as good as it can with what I have.
Cliff Ruggles:
Part of the stumble off idle issue could also be the engine build.
The aluminum intake isn't helping nor is the larger than stock camshaft. If the heads were ever off or engine rebuilt it will almost always have a LOT more squish distance than the original engine did as aftermarket head gaskets are a LOT thicker than the factory .020" steel shim gaskets they used back then.
I see this sort of thing ALL THE TIME.
Well meaning folks make changes to the engine thinking that there are improving power and performance and more times than not they are hurting it.
I'm not familiar with that carburetor part number, might be a SR carb? Is it a single main airbleed model?........Cliff
dphipps:
I have never had the heads off and the truck is pretty low mileage so I don't think they've ever been off.
Is the cam really a problem? It was pretty much the smallest there was so I didn't think it would be much issue. The aluminum intake is just a dual plane and I was told it's mostly a copy of the stock one.
The stumble issue went away with the accelerator pump disabled. Even spun the tires!
I'm not sure how to identify the air bleed question.. I just dug out the book and I'm going to say it is not a single main air bleed.
I attached a picture of the airhorn.
dphipps:
Also, I was advised to try going up a jet size when I put headers on so that's all that has been changed from the factory calibration. I guess I'm mainly wondering how the current calibration looks.
Cliff Ruggles:
Things done to the engine to improve efficiency may have it wanting LESS fuel, not more fuel.
I've never been overly fond of the RV camshaft they sell for SBC engines. It's a solid 10 degrees bigger than a stock cam everyplace and unless the compression ratio is raised at least one full point everything suffers....idle quality, throttle response, efficiency at low RPM's, etc.
The best cam to use in a stock compression ratio 350 CID build with smog era 76cc iron heads on it is the Speed Pro CS-274.....IMHO......Cliff
Navigation
[0] Message Index
[#] Next page
Go to full version