News:
We buy American, and use American Made parts for all of our exclusive Cliff's Carburetor parts and kits.
| Subject / Started by | Replies / Views | Last post  |
||
|---|---|---|---|---|
|
|
Which carb is best for MPG?
Started by rich ullsmith |
3 Replies
4578 Views |
June 09, 2012, 03:22:36 AMby Cliff Ruggles |
|
|
|
Increasing cfm?
Started by Marx3 |
3 Replies
6179 Views |
June 05, 2012, 03:28:54 AM by Cliff Ruggles |
|
|
|
Holes plugged in main body.
Started by PUO |
3 Replies
5424 Views |
June 05, 2012, 03:15:38 AM by Cliff Ruggles |
|
|
|
1 Replies
3073 Views |
June 05, 2012, 03:09:27 AM by Cliff Ruggles |
|
|
|
|
1 Replies
2941 Views |
June 01, 2012, 06:29:39 AM by Cliff Ruggles |
|
|
|
|
Do I need to add idle bypass air?
Started by gtome |
1 Replies
3940 Views |
June 01, 2012, 06:28:21 AM by Cliff Ruggles |
|
|
|
Best carb to use
Started by bigchief |
2 Replies
3193 Views |
May 29, 2012, 11:43:14 AM by bigchief |
|
|
|
Unusual Secondary Jet Repair
Started by levyb |
1 Replies
2629 Views |
May 29, 2012, 04:17:04 AM by Cliff Ruggles |
|
|
|
1 Replies
2743 Views |
May 25, 2012, 04:29:27 AM by Cliff Ruggles |
|
|
|
|
Can the EGR port be used for dist vacuum?
Started by gkz |
1 Replies
2795 Views |
May 25, 2012, 04:28:16 AM by Cliff Ruggles |
|
|
|
Thanks for...
Started by gkz |
1 Replies
2677 Views |
May 25, 2012, 04:26:30 AM by Cliff Ruggles |
|
|
|
Air Horn/ Top of Carb
Started by freezy64 |
2 Replies
3808 Views |
May 21, 2012, 06:48:38 PM by freezy64 |
|
|
10 Replies
7186 Views |
May 21, 2012, 03:28:47 AM by Cliff Ruggles |
|
|
|
|
DRILLING OUT BOTTOM PLUGS?
Started by turbo210 |
4 Replies
4086 Views |
May 20, 2012, 02:40:41 AM by Cliff Ruggles |
|
|
|
Use little clip on end of needle?
Started by daveo76 |
1 Replies
2883 Views |
May 19, 2012, 11:21:34 PM by daveo76 |
|
|
|
STAGGERED JETTING
Started by qjetsrule |
1 Replies
3382 Views |
May 17, 2012, 03:27:28 PM by TommyK |
|
|
|
3 Replies
5205 Views |
May 17, 2012, 03:41:44 AM by Cliff Ruggles |
|
|
|
|
Cliff, 17056240 advice needed: A.s.a.p
Started by Mr.Pontiac |
5 Replies
4255 Views |
May 16, 2012, 04:31:34 AM by Cliff Ruggles |
|
|
|
Baseplate Idle Mixture Holes
Started by Rhett |
1 Replies
2921 Views |
May 15, 2012, 02:21:03 PM by Rhett |
|
|
|
Secondary Throttle Plate Opening Angle
Started by Rhett |
2 Replies
3316 Views |
May 10, 2012, 04:46:49 AM by Cliff Ruggles |
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll