Author Topic: extra piece after rebuilding quadrajet  (Read 3509 times)

Offline shanes77ta

  • Garage guy
  • **
  • Posts: 5
extra piece after rebuilding quadrajet
« on: September 13, 2013, 06:32:45 PM »
hey guys, i am curious if any of you have seen where this piece that i have after rebuilding my quadrajet goes or came from... I have a solid green pin that i cannot figure out where it goes. it is approximately 3/16 inches in diameter and 3/4 inches long..

Offline shanes77ta

  • Garage guy
  • **
  • Posts: 5
Re: extra piece after rebuilding quadrajet
« Reply #1 on: September 13, 2013, 06:37:52 PM »
also, it came out of a 1983 caprice wagon and the casting number is 17084208.

Offline shanes77ta

  • Garage guy
  • **
  • Posts: 5
Re: extra piece after rebuilding quadrajet
« Reply #2 on: September 13, 2013, 06:50:52 PM »
here is a picture

Offline Ethan1

  • Moderator
  • Qjet Hero
  • *****
  • Posts: 1148
Re: extra piece after rebuilding quadrajet
« Reply #3 on: September 13, 2013, 07:15:55 PM »
here is a picture

 Welcome to CHP!

 That piece looks to be the pushrod for the throttle position sensor and acts as a plunger. If you turn the air horn upside down, you will see the lever for the TPS and a hole right beside it. That is where it goes.
Ethan

1972 Chevelle

(oo______oo)

Offline shanes77ta

  • Garage guy
  • **
  • Posts: 5
Re: extra piece after rebuilding quadrajet
« Reply #4 on: September 14, 2013, 06:51:34 AM »
sorry for this response as it is very novice but this was the first carb i have opened up/rebuilt. i have always had someone else help with the carb stuff so... what is the air horn? also i always say im from missouri, show me... im not up on my terminology yet.

thank you for the help!

Offline Ethan1

  • Moderator
  • Qjet Hero
  • *****
  • Posts: 1148
Re: extra piece after rebuilding quadrajet
« Reply #5 on: September 14, 2013, 03:15:30 PM »
sorry for this response as it is very novice but this was the first carb i have opened up/rebuilt. i have always had someone else help with the carb stuff so... what is the air horn? also i always say im from missouri, show me... im not up on my terminology yet.

thank you for the help!

 Not a problem. The air horn is the top part of the carb, the float bowl is middle part of the carb and throttle body is the bottom part of the carb. So, you will have three main pieces when taken apart. The throttle position sensor or TPS, is located on the driver side front of the carb. Should be a white or black electrical plug sticking out, before you took it apart.

 Here is the part you need help on, that you don't know where it goes. I am not a 100% sure, but it is the only part I can think of it being.

 
Ethan

1972 Chevelle

(oo______oo)

Offline Ethan1

  • Moderator
  • Qjet Hero
  • *****
  • Posts: 1148
Re: extra piece after rebuilding quadrajet
« Reply #6 on: September 14, 2013, 03:18:12 PM »
 You can see the plunger in the above photo. It is the one near the TPS lever, where you can see the green plunger sticking out alittle.
Ethan

1972 Chevelle

(oo______oo)

Offline shanes77ta

  • Garage guy
  • **
  • Posts: 5
Re: extra piece after rebuilding quadrajet
« Reply #7 on: September 16, 2013, 04:57:25 PM »
wow, awesome info! thanks for the help! now just to put it back in the car and see if it will run.