Quadrajet Problem Solving > Dialing in your rebuilt Quadrajet carburetor

Which Recipe Best For My Setup?

(1/5) > >>

Tinkerman:
Hello,

Have been lurking and learning for several months and just joined. I bought Cliff's book several years ago and it has been very handy. Right now, I am struggling to determine which of the recipes in Cliff's book would be best for my carb.

I am in the process of restoring a numbers matching 69 Camaro Pace Car with the 350/300 L48 engine, TH350 auto trans, 3.31 rear axle, and F40-14 tires.

I am rebuilding the engine to the following specifications:

- Bored 0.030 over to 355 cubic inches
- 10.25:1 compression ratio
- Original exhaust manifolds with new OEM exhaust system
- Original heads and cast iron intake
- AC Delco R45 spark plugs (a little hotter than original R43 plugs)
- Will be using 93 octane pure gas

I am installing a retrofit hydraulic roller camshaft with the following specs:
- Stage 3 cam profile
- Duration at 0.050" is 215 Intake/230 Exhaust
- Advertised duration is 284 Intake and 310 Exhaust
- Valve lift is 0.470" Intake and 0.480" Exhaust using 1.6 ratio pushrods
- LSA is 114. Actually states Intake 106 and Exhaust 114
- Power range is 1700-5500 RPM

I have the original Carter built 7029202 carb. The carb is in good shape with no warping between the air horn, main body, or throttle body.

With a 114 LSA, I am trying to figure out what I would have for manifold vacuum at idle. I am thinking 12-15 psi but not sure.

My initial inclination is to use Recipe 1 from Cliff's book. Would that be the right one for my setup?

Thanks!
Dan

Cliff Ruggles:
The 1969 and 1970 Chevy 350/300hp engines was one of the best engines to ever leave Detroit in any of those applications.  It had high compression, tight quench, efficient combustion chambers and very well chosen camshaft.

They idle smooth without much timing in them, strong power to at least 5000rpm's and very efficient.  I had one in a 1970 Impala as a daily driver and it would knock down 20-24mpg's w/o overdrive and roast the tires right off the car at will.

Moving up to a larger cam without increasing the compression ratio will soften it up some, especially idle and off idle so you'll have to use larger idle tubes to put more fuel to the idle mixture screws.

I would set the carb up closer to the 7029207 unit which had more idle fuel since those engines used much larger camshafts.

Do NOT drill any airbleeds on that unit.  When you are ready to do the build call me at the shop and I'll set you up with what is needed to duplicate the 7029207 specs.

It is imperative to make sure that you establish tight quench during the rebuild.  The factory kept the quench under .040" by using a .020" steel shim head gasket with the pistons pretty close to the top of the block at TDC.

99 percent of the folks who rebuild those engines buy "builder" pistons that sit much lower in the block at TDC and add a THICK head gasket.  This will lower the compression ratio, hurt engine efficiency, run hotter/overheat/ping on pump gas and kill off considerable engine power.

I get calls from folks all the time who have built SBC 350 engines and very unhappy with them simply because they did not pay close attention to detail and keep the quench super-tight in them.......Cliff

Tinkerman:
Cliff,

Roger that and thanks for the info. I will speak with my engine builder to ensure we keep the quench under 0.040". I don't want to deck the block as it still has the Tonawanda build date stamp on the engine pad.

I have torn down my carb to get the current measurements on everything and am ready to begin the rebuild process. I will give you a call so we can build it to the 7029207 specs.

Thanks again,
Dan

old cars:
I am installing a retrofit hydraulic roller camshaft with the following specs:
- Stage 3 cam profile
- Duration at 0.050" is 215 Intake/230 Exhaust
- Advertised duration is 284 Intake and 310 Exhaust
- Valve lift is 0.470" Intake and 0.480" Exhaust using 1.6 ratio pushrods
- LSA is 114. Actually states Intake 106 and Exhaust 114
- Power range is 1700-5500 RPM

May I ask who is the camshaft supplier?

Tinkerman:
The cam is an Engine Pro part# MC22136. I think they are related to Melling somehow as this is a Melling's grind.

Thanks,
Dan

Navigation

[0] Message Index

[#] Next page

Go to full version