News:
We buy American, and use American Made parts for all of our exclusive Cliff's Carburetor parts and kits.
| Subject / Started by | Replies / Views  |
Last post | ||
|---|---|---|---|---|
|
|
Drilling
Started by 68_rodderjoe |
1 Replies
2512 Views |
November 26, 2009, 03:11:05 PMby Cliff Ruggles |
|
|
|
454 marine 17080560 questions
Started by Okie BB |
3 Replies
2511 Views |
December 10, 2011, 05:11:56 AM by Cliff Ruggles |
|
|
|
6 Replies
2509 Views |
March 19, 2015, 03:12:33 PM by blazer74 |
|
|
|
Outer booster removal project?
Started by 77cruiser |
10 Replies
2508 Views |
October 09, 2017, 05:50:21 AM by 77cruiser |
|
|
|
2 Replies
2508 Views |
February 05, 2013, 06:24:51 AM by Kjetil |
|
|
|
|
accelerator pump shaft.
Started by omaha |
1 Replies
2507 Views |
May 13, 2009, 06:34:10 AM by Cliff Ruggles |
|
|
|
Rod hanger 'G' or higher?
Started by dayzedandkonfuzed |
2 Replies
2507 Views |
February 27, 2013, 05:07:12 AM by Cliff Ruggles |
|
|
|
hot idle compensator
Started by tom t |
2 Replies
2507 Views |
July 30, 2016, 03:48:14 PM by tom t |
|
|
|
Original jets & rods
Started by 77cruiser |
2 Replies
2506 Views |
May 26, 2010, 11:53:24 AM by 77cruiser |
|
|
|
E10/15 fuel and vapor lock.
Started by old blue 75 |
10 Replies
2499 Views |
June 25, 2020, 09:24:19 PM by blazer74 |
|
|
|
Secondary tube restriction
Started by beertracker |
6 Replies
2497 Views |
December 19, 2014, 08:56:29 PM by beertracker |
|
|
|
Carb dumping Too Much Fuel
Started by cutlassrichard |
2 Replies
2493 Views |
April 15, 2011, 11:10:30 AM by cutlassrichard |
|
|
|
carb. interchange
Started by jk79ta |
4 Replies
2485 Views |
July 08, 2011, 04:36:08 AM by jk79ta |
|
|
|
3 Replies
2481 Views |
March 31, 2011, 08:24:37 PM by pggto |
|
|
|
|
Mopar Qjets
Started by Marx3 |
6 Replies
2479 Views |
June 27, 2013, 04:42:29 AM by Cliff Ruggles |
|
|
|
350 Powered Snowblower
Started by Bob_T |
6 Replies
2476 Views |
January 24, 2017, 08:00:04 AM by Bob_T |
|
|
|
1 Replies
2474 Views |
August 08, 2014, 04:38:38 AM by Cliff Ruggles |
|
|
|
|
Choke Pull-Off Vacuum Line
Started by Ethan1 |
0 Replies
2470 Views |
June 13, 2010, 10:36:08 AM by Ethan1 |
|
|
|
Base Plate Removal Question
Started by FirebirdMan68 |
2 Replies
2470 Views |
February 13, 2011, 03:18:08 PM by marcs78ta |
|
|
|
E4ME measurements any thoughts?
Started by Peer81 |
4 Replies
2466 Views |
June 08, 2011, 09:37:22 AM by Peer81 |
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll