News:
Buy "The Book" on Q-jets and OverDrive Transmission Swaps. On the Website Home Page!
| Subject / Started by | Replies  / Views |
Last post | ||
|---|---|---|---|---|
|
|
Cliff, need you advice on needle seat
Started by Mr.Pontiac |
2 Replies
2744 Views |
July 13, 2012, 04:22:11 AMby Cliff Ruggles |
|
|
|
Can these idle tubes be re used?
Started by Kjetil |
2 Replies
2785 Views |
September 15, 2012, 06:26:30 AM by Kjetil |
|
|
|
Sticky secondaries
Started by gtome |
2 Replies
2663 Views |
September 17, 2012, 05:11:44 AM by Cliff Ruggles |
|
|
|
2 Replies
3751 Views |
October 15, 2010, 04:05:35 PM by sdowney717 |
|
|
|
|
throttle shafts
Started by bradhooker |
2 Replies
3352 Views |
September 16, 2010, 07:43:16 PM by bradhooker |
|
|
|
Specifics For .120 Main Air Bleed QJets
Started by craigb93 |
2 Replies
3547 Views |
August 22, 2010, 05:11:48 AM by Cliff Ruggles |
|
|
|
2 Replies
794 Views |
October 25, 2025, 01:01:38 PM by Cadman-iac |
|
|
|
|
Base Plate Removal Question
Started by FirebirdMan68 |
2 Replies
3781 Views |
February 13, 2011, 03:18:08 PM by marcs78ta |
|
|
|
primary throttle shaft
Started by Michael9040 |
2 Replies
3484 Views |
August 16, 2010, 04:21:12 AM by Cliff Ruggles |
|
|
|
Recipes @ altitude
Started by SundanceKid |
2 Replies
3647 Views |
May 27, 2010, 09:19:15 PM by SundanceKid |
|
|
|
Quadrajet for 78 Chevy van
Started by clutch442 |
2 Replies
3557 Views |
July 10, 2010, 05:59:17 AM by clutch442 |
|
|
|
2 Replies
3461 Views |
November 12, 2010, 10:17:25 AM by kelley555 |
|
|
|
|
Make the bypass air easily adjustable
Started by spoolboy |
2 Replies
1491 Views |
April 06, 2025, 06:20:00 AM by Cliff Ruggles |
|
|
|
E85 conversion?
Started by larrywalk |
2 Replies
6033 Views |
January 09, 2010, 02:31:07 PM by Cliff Ruggles |
|
|
|
7040570 3055
Started by JamRSW6 |
2 Replies
2769 Views |
June 27, 2013, 04:44:41 AM by Cliff Ruggles |
|
|
|
Jetting Question
Started by WhiteC3 |
2 Replies
4574 Views |
November 26, 2009, 03:08:38 PM by Cliff Ruggles |
|
|
|
Anything special about Caddy carbs?
Started by omaha |
2 Replies
2955 Views |
January 07, 2011, 10:50:33 AM by omaha |
|
|
|
Milling the choke housing.
Started by omaha |
2 Replies
2959 Views |
January 13, 2011, 04:59:51 AM by Cliff Ruggles |
|
|
|
2 Replies
2974 Views |
August 20, 2013, 05:58:13 AM by Cliff Ruggles |
|
|
|
|
2 Replies
3145 Views |
August 08, 2013, 10:19:33 AM by pex006 |
|
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll