News:
2000+ Members and Counting!
The best Quadrajet Carburetor Forum on the web.
| Subject / Started by | Replies / Views  |
Last post | ||
|---|---|---|---|---|
|
|
Cliff R ? / Is this a SR carb and .....
Started by PMD1969 |
3 Replies
2892 Views |
October 30, 2014, 10:45:44 AMby PMD1969 |
|
|
|
Which one to rebuild.
Started by 68imp |
2 Replies
2895 Views |
May 14, 2013, 03:58:12 AM by Cliff Ruggles |
|
|
|
3 Replies
2896 Views |
January 06, 2011, 04:17:05 AM by Cliff Ruggles |
|
|
|
|
Accelerator pump arm adjustment
Started by tayto |
1 Replies
2897 Views |
November 19, 2015, 02:34:13 AM by Cliff Ruggles |
|
|
|
Baseline settings? 455 Pontiac
Started by Zippy |
2 Replies
2899 Views |
August 19, 2013, 06:51:18 PM by Ethan1 |
|
|
|
Qjet build questions
Started by TransAm 474 |
1 Replies
2901 Views |
February 22, 2015, 05:21:01 AM by Cliff Ruggles |
|
|
|
idle tubes
Started by 808olds |
1 Replies
2908 Views |
October 19, 2010, 03:49:22 AM by Cliff Ruggles |
|
|
|
1 Replies
2909 Views |
August 26, 2010, 03:29:18 AM by Cliff Ruggles |
|
|
|
|
Carb recipe
Started by firebird*boz |
1 Replies
2910 Views |
March 22, 2011, 11:53:16 PM by omaha |
|
|
|
Quadrajet - '69 GTO 400 (non R.Air)
Started by tweist |
3 Replies
2911 Views |
February 17, 2015, 07:33:17 AM by tweist |
|
|
|
secondary air flap shaft looseness
Started by sticknstring |
1 Replies
2911 Views |
February 10, 2011, 03:49:26 AM by Cliff Ruggles |
|
|
|
Is clip mandatory on needle ?
Started by Frank400 |
1 Replies
2915 Views |
May 04, 2012, 04:14:23 AM by Cliff Ruggles |
|
|
|
secondary air door - Edelbrock 1910
Started by novadude |
3 Replies
2918 Views |
May 14, 2013, 03:59:48 AM by Cliff Ruggles |
|
|
|
ID a Q-Jet from a picture
Started by trotterlg |
4 Replies
2921 Views |
October 09, 2012, 02:04:56 PM by trotterlg |
|
|
|
3 Replies
2922 Views |
March 06, 2015, 03:24:25 PM by Cliff Ruggles |
|
|
|
|
modify or purchase correct carb
Started by Tom Lynch |
4 Replies
2925 Views |
September 17, 2012, 02:24:14 PM by Tom Lynch |
|
|
|
early APT screw removal
Started by Frank400 |
4 Replies
2930 Views |
March 28, 2017, 06:49:28 AM by Mudsport96 |
|
|
|
Un-warping jig
Started by Pav8427 |
6 Replies
2930 Views |
March 03, 2018, 03:11:41 AM by Pav8427 |
|
|
|
Need help with a hot start issue
Started by johnt365 |
2 Replies
2930 Views |
June 06, 2011, 05:55:35 PM by slowpoke |
|
|
|
E4ME design evolution?
Started by Peer81 |
1 Replies
2930 Views |
March 03, 2010, 05:01:13 AM by Cliff Ruggles |
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll