News:
We buy American, and use American Made parts for all of our exclusive Cliff's Carburetor parts and kits.
| Subject / Started by | Replies / Views  |
Last post | ||
|---|---|---|---|---|
|
|
Ccc help
Started by Breakneck88 |
1 Replies
3604 Views |
June 21, 2013, 04:05:25 AMby Cliff Ruggles |
|
|
|
Quadrajet on a 250l6?
Started by jachristmas |
6 Replies
3601 Views |
June 25, 2023, 08:48:40 AM by jachristmas |
|
|
|
secondary airflap question.
Started by firebird*boz |
3 Replies
3600 Views |
June 26, 2011, 05:16:32 AM by Cliff Ruggles |
|
|
|
7 Replies
3600 Views |
January 24, 2025, 12:52:40 PM by GSP7 |
|
|
|
|
Cliff R ? / Is this a SR carb and .....
Started by PMD1969 |
3 Replies
3599 Views |
October 30, 2014, 10:45:44 AM by PMD1969 |
|
|
|
Cliff maybe im wrong!! Need your help
Started by Mr.Pontiac |
2 Replies
3598 Views |
October 19, 2011, 04:42:12 PM by Mr.Pontiac |
|
|
|
E4ME design evolution?
Started by Peer81 |
1 Replies
3598 Views |
March 03, 2010, 05:01:13 AM by Cliff Ruggles |
|
|
|
Accelerator pump arm adjustment
Started by tayto |
1 Replies
3596 Views |
November 19, 2015, 02:34:13 AM by Cliff Ruggles |
|
|
|
Quadrajet - '69 GTO 400 (non R.Air)
Started by tweist |
3 Replies
3596 Views |
February 17, 2015, 07:33:17 AM by tweist |
|
|
|
APT on a 75 q-jet
Started by deanhickey |
7 Replies
3592 Views |
September 29, 2022, 06:29:36 PM by tayto |
|
|
|
Air Bleeds question
Started by Sonny |
6 Replies
3587 Views |
October 30, 2018, 02:06:51 AM by Cliff Ruggles |
|
|
|
secondary air door - Edelbrock 1910
Started by novadude |
3 Replies
3584 Views |
May 14, 2013, 03:59:48 AM by Cliff Ruggles |
|
|
|
Is clip mandatory on needle ?
Started by Frank400 |
1 Replies
3579 Views |
May 04, 2012, 04:14:23 AM by Cliff Ruggles |
|
|
|
PCV to the REAR, OK?
Started by garybohannon |
1 Replies
3572 Views |
April 17, 2011, 11:24:27 AM by Schurkey |
|
|
|
Quadrajet air valve operation
Started by 73 Z28 |
2 Replies
3568 Views |
January 04, 2012, 11:15:57 PM by Schurkey |
|
|
|
Idle Air Vent
Started by MBP |
6 Replies
3564 Views |
March 17, 2023, 03:25:27 AM by Cliff Ruggles |
|
|
|
Quesiton on Drilling Idle Tubes
Started by WideTrack |
2 Replies
3562 Views |
May 13, 2020, 07:53:04 PM by WideTrack |
|
|
|
Reinstalling idle tubes
Started by Greasy Harley |
5 Replies
3562 Views |
October 16, 2018, 08:27:24 PM by Greasy Harley |
|
|
|
Base plate repair or replace
Started by trans am greg |
3 Replies
3561 Views |
September 11, 2016, 08:03:21 AM by omaha |
|
|
|
Quadrajet 4MV 1968 Camaro
Started by CaliChevyV8 |
1 Replies
3557 Views |
December 03, 2011, 07:30:58 AM by Cliff Ruggles |
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll