News:
We buy American, and use American Made parts for all of our exclusive Cliff's Carburetor parts and kits.
| Subject / Started by | Replies / Views  |
Last post | ||
|---|---|---|---|---|
|
|
Jet sizes for a stock Pontiac 455
Started by Blockman301 |
3 Replies
2598 Views |
January 06, 2018, 05:23:38 AMby Cliff Ruggles |
|
|
Lean condition at idle only
Started by jberenyi |
10 Replies
2597 Views |
April 21, 2022, 09:41:32 AM by Cliff Ruggles |
|
|
|
1 Replies
2596 Views |
September 10, 2020, 04:40:33 AM by Cliff Ruggles |
|
|
|
|
Cadillac carb on stock 305
Started by Bludacious |
8 Replies
2593 Views |
November 27, 2019, 02:11:27 PM by davel |
|
|
|
1 Replies
2593 Views |
June 05, 2012, 03:09:27 AM by Cliff Ruggles |
|
|
|
|
17083221 Quadrajet
Started by jimmyg |
6 Replies
2593 Views |
October 28, 2018, 06:11:48 AM by Cliff Ruggles |
|
|
|
stock idle circuit for 7029207
Started by novadude |
2 Replies
2589 Views |
January 17, 2014, 04:29:13 PM by novadude |
|
|
|
1 Replies
2588 Views |
February 20, 2012, 04:03:05 AM by Cliff Ruggles |
|
|
|
|
Front fuel inlet carb on a SBC 350
Started by murphy |
3 Replies
2585 Views |
August 27, 2012, 07:57:09 AM by murphy |
|
|
|
secondary hanger and gasket thickness
Started by D Denzin |
3 Replies
2584 Views |
June 30, 2014, 05:36:46 AM by Cliff Ruggles |
|
|
|
base plate locating pins
Started by firebird*boz |
1 Replies
2584 Views |
June 12, 2011, 03:00:04 AM by Cliff Ruggles |
|
|
|
Need some quick help with a 708 style
Started by vic_v8 |
3 Replies
2584 Views |
April 14, 2015, 08:08:45 PM by vic_v8 |
|
|
|
Power Piston Assy Hanger spring
Started by Gearheadzs |
4 Replies
2583 Views |
January 04, 2013, 10:07:55 AM by Shark Racer |
|
|
|
Float Bowl Volume
Started by lsp |
3 Replies
2583 Views |
June 30, 2014, 05:35:35 AM by Cliff Ruggles |
|
|
|
idle air tube
Started by wseeley |
3 Replies
2582 Views |
December 20, 2013, 05:19:17 AM by wseeley |
|
|
|
float level and consequences question
Started by Frank400 |
2 Replies
2579 Views |
June 12, 2014, 04:56:20 AM by Cliff Ruggles |
|
|
|
1 Replies
2579 Views |
March 18, 2010, 05:09:53 AM by Cliff Ruggles |
|
|
|
|
Milling the choke housing.
Started by omaha |
2 Replies
2577 Views |
January 13, 2011, 04:59:51 AM by Cliff Ruggles |
|
|
|
17058531 opinions?
Started by sleddogg |
3 Replies
2576 Views |
July 30, 2015, 08:44:01 AM by sleddogg |
|
|
|
Edelbrock 1910 Primary throttle shaft
Started by novadude |
2 Replies
2572 Views |
November 01, 2013, 05:32:07 AM by novadude |
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll