News:
Need a Budget Carb Rebuild Kit? Check out our $45.95 SR Kits. Same Top Quality Parts as the Full Kits.
| Subject / Started by | Replies / Views  |
Last post | ||
|---|---|---|---|---|
|
|
17058531 opinions?
Started by sleddogg |
3 Replies
2554 Views |
July 30, 2015, 08:44:01 AMby sleddogg |
|
|
|
Edelbrock 1910 Primary throttle shaft
Started by novadude |
2 Replies
2552 Views |
November 01, 2013, 05:32:07 AM by novadude |
|
|
|
Car wont idle after the choke comes off.
Started by chgohr |
1 Replies
2547 Views |
November 12, 2013, 03:42:04 AM by Cliff Ruggles |
|
|
|
Cracked Base Plate
Started by cutlassrichard |
1 Replies
2547 Views |
April 19, 2011, 04:44:26 AM by Cliff Ruggles |
|
|
|
Can these idle tubes be re used?
Started by Kjetil |
2 Replies
2546 Views |
September 15, 2012, 06:26:30 AM by Kjetil |
|
|
|
New Pontiac Build with Quadrajet
Started by streetfighter |
3 Replies
2546 Views |
July 11, 2015, 06:07:38 AM by streetfighter |
|
|
|
Idle bypass air hole size?
Started by afmuse76 |
3 Replies
2544 Views |
July 04, 2013, 09:23:05 AM by Shark Racer |
|
|
|
Secondary well size
Started by novadude |
3 Replies
2544 Views |
January 07, 2017, 03:57:07 AM by Cliff Ruggles |
|
|
|
fuel needle seat
Started by stevef |
2 Replies
2543 Views |
April 18, 2016, 06:13:05 PM by stevef |
|
|
|
3 Replies
2542 Views |
September 17, 2013, 06:55:28 AM by 77cruiser |
|
|
|
|
Dodge Qjet idle mixture screw question
Started by 76PW200 |
2 Replies
2539 Views |
April 25, 2016, 01:20:00 AM by Cliff Ruggles |
|
|
|
Vacuum caps
Started by Huddie |
1 Replies
2537 Views |
September 19, 2010, 05:01:22 PM by clutch442 |
|
|
|
another question, this one is self induced!
Started by v737d |
4 Replies
2536 Views |
July 03, 2013, 05:46:44 AM by v737d |
|
|
|
linkage and spring
Started by petes70 |
1 Replies
2535 Views |
February 22, 2011, 03:36:06 AM by Cliff Ruggles |
|
|
|
assembly tips
Started by 73ss |
1 Replies
2534 Views |
February 20, 2012, 04:02:08 AM by Cliff Ruggles |
|
|
|
3 Replies
2533 Views |
November 23, 2013, 09:13:03 AM by makomark |
|
|
|
|
Marine Tex not very user friendly
Started by Frank400 |
4 Replies
2531 Views |
February 23, 2016, 03:06:30 AM by Cliff Ruggles |
|
|
|
My First Plating Job
Started by WideTrack |
3 Replies
2531 Views |
April 30, 2020, 08:21:23 PM by qjetsrule |
|
|
|
2 gc for a 350 chevy 275 hp
Started by pat469 |
2 Replies
2530 Views |
March 27, 2014, 03:08:04 PM by pat469 |
|
|
|
Is it possible?
Started by 80PCTA |
1 Replies
2529 Views |
November 16, 2012, 01:32:41 AM by Cliff Ruggles |
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll