News:
We buy American, and use American Made parts for all of our exclusive Cliff's Carburetor parts and kits.
| Subject / Started by | Replies / Views | Last post  |
||
|---|---|---|---|---|
|
|
Edelbrock 1904 questions
Started by MikeB |
3 Replies
3457 Views |
October 21, 2014, 04:24:23 AMby Cliff Ruggles |
|
|
|
4 Replies
5007 Views |
September 27, 2014, 08:59:08 PM by 429bbf |
|
|
|
|
Primary Choke Pull-Off/Bracket
Started by Ethan1 |
3 Replies
3000 Views |
September 18, 2014, 03:31:03 AM by Cliff Ruggles |
|
|
|
Needle & Seat
Started by 1969GTO |
1 Replies
3184 Views |
July 31, 2014, 04:38:42 AM by Cliff Ruggles |
|
|
|
secondary choke pull off
Started by j_oetjens |
2 Replies
3409 Views |
June 17, 2014, 06:15:25 AM by Mr.Pontiac |
|
|
|
Where can I find this Qjet part ?
Started by PMD1969 |
1 Replies
2990 Views |
May 28, 2014, 02:05:58 AM by Cliff Ruggles |
|
|
|
46M primary metering rods
Started by Matte |
3 Replies
3559 Views |
May 08, 2014, 03:15:42 AM by Cliff Ruggles |
|
|
|
1 Replies
2750 Views |
May 02, 2014, 04:43:30 AM by Cliff Ruggles |
|
|
|
|
3 Replies
3845 Views |
April 25, 2014, 04:08:38 AM by Cliff Ruggles |
|
|
|
|
1 Replies
3020 Views |
March 27, 2014, 04:52:56 PM by Cliff Ruggles |
|
|
|
|
Cliff, can you supply such idle tubes ?
Started by Frank400 |
1 Replies
2806 Views |
March 27, 2014, 04:49:26 PM by Cliff Ruggles |
|
|
|
2 Replies
3035 Views |
March 15, 2014, 04:21:58 AM by Cliff Ruggles |
|
|
|
|
Float needle seat
Started by Jimpala |
1 Replies
2690 Views |
March 15, 2014, 04:19:32 AM by Cliff Ruggles |
|
|
|
4 Replies
3775 Views |
March 08, 2014, 05:58:05 AM by carmantx |
|
|
|
|
1 Replies
3152 Views |
February 01, 2014, 04:00:19 AM by Cliff Ruggles |
|
|
|
Which carb?
Started by TGB350LeMans |
10 Replies
8181 Views |
February 01, 2014, 03:59:14 AM by Cliff Ruggles |
|
|
|
Carb re-rebuild
Started by dblakey |
1 Replies
2783 Views |
January 23, 2014, 12:46:00 AM by omaha |
|
|
|
jet and rod advise needed
Started by REFORMULATED |
6 Replies
4556 Views |
December 13, 2013, 04:04:32 AM by Cliff Ruggles |
|
|
|
M4MC power piston
Started by novadude |
1 Replies
2488 Views |
December 09, 2013, 03:34:12 AM by Cliff Ruggles |
|
|
|
Who grinds your drill bits Cliff??
Started by Mr.Pontiac |
4 Replies
3803 Views |
December 04, 2013, 04:53:08 AM by Cliff Ruggles |
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll