Author Topic: Secondary hanger and rods?  (Read 1539 times)

Offline Jeff K

  • Garage guy
  • **
  • Posts: 44
Secondary hanger and rods?
« on: September 12, 2023, 06:40:58 AM »
I have a 1978 Chevy 454 truck motor. It has 8.25 compression it it all stock but runs very strong. This is in a 69 el Camino with a th400 and 2.73 standard cog 10 bolt. This is a street car only and I am very happy with the power it gives.

I recently changed cams to the Melling 22216 marine cam with new GM lifters with the split base.

I am thrilled with the additional performance of this cam, along with its cool, low key, lope at idle..

My brother gave me three Quadrajets, he is cleaning out one of his storage spots. God only knows what he has stashed away. One of the carbs has a straight in fuel filter and the other two have 90 degree inlets. He says one style is for Pontiacs and hard to get..

I have three hangers and four sets of rods.
2- L hangers.
1- J hanger.

2 sets of CK rods #7045779 S-tip.
1 set of DP rods  #0686 S tip.
What would be the best hanger and set of rods to use. Or do I have to do experiment..

The carb I have on the engine is stock and came with the engine.

My car likes the air and fuel mixture set at 3 and 3/4s turns for the best idle to off idle performance. This makes a very big difference in off idle performance. Its real strong off idle all the way to 5500...

Cliff, thank you so much for the cam recommendation!!!


Offline Cliff Ruggles

  • Administrator
  • Qjet Hero
  • *****
  • Posts: 5408
Re: Secondary hanger and rods?
« Reply #1 on: September 18, 2023, 02:38:16 AM »
What carburetor is on it now?  What secondary metering rods?

Offline Jeff K

  • Garage guy
  • **
  • Posts: 44
Re: Secondary hanger and rods?
« Reply #2 on: September 18, 2023, 05:58:06 AM »
Thanks Cliff, but I found the info in your book of all places LOL..

Offline Jeff K

  • Garage guy
  • **
  • Posts: 44
Re: Secondary hanger and rods?
« Reply #3 on: September 21, 2023, 07:52:58 AM »
Turns out I didn't have the right parts.

-The engine is a stock 1978 Chevrolet 454 truck motor. 8.20 compression, no emmisions, the only modification is the 22216 Melling cam.

-Th-400 2.73.

The Quadrajet carb looks like its the one that came with the 1978 454 truck engine.

-Right now Im using a L hanger with DH rods.

 I have the following extra parts;

- I, J and L hangers.

- 2 sets of CH rods and one set of DP rods..

Its running pretty good and has strong power in all ranges. I just wanted to make sure I'm using the best parts for the rest of the season.

This winter, I'm going to completely go over it with one of your kits. I think it might need a small brass float.

I can get some better pictures once my camera charges.


             


Offline Jeff K

  • Garage guy
  • **
  • Posts: 44
Re: Secondary hanger and rods?
« Reply #4 on: September 22, 2023, 03:27:13 AM »
The carb numbers on the left side are 17058212 then under that is 1218 BJA..

I'm using the L hanger with the DH rods that are suppose to be short tip.

I also have a set of CH and DP rods along with a J and I hangers..


Offline Cliff Ruggles

  • Administrator
  • Qjet Hero
  • *****
  • Posts: 5408
Re: Secondary hanger and rods?
« Reply #5 on: September 22, 2023, 04:25:07 AM »
I just rebuilt and recalibrated that same carb for a customers who made some engine modifications.  It had small main jets and really small primary metering rods in it and not doing well for him. 

I went to bigger jets, metering rods and external APT in the baseplate.  I also opened up the idle tubes and went to DA secondary metering rods. 

The biggest problem I found with his is that it had been previously rebuilt and had a small N/S assembly in it and not keeping the bowl full. 

Let me know when you are ready to do the rebuild and we can go over some specifics then and make a few changes to help it out some.....

Offline Jeff K

  • Garage guy
  • **
  • Posts: 44
Re: Secondary hanger and rods?
« Reply #6 on: September 22, 2023, 06:47:08 AM »
Will do, thanks so much..