News:
We buy American, and use American Made parts for all of our exclusive Cliff's Carburetor parts and kits.
| Subject / Started by | Replies  / Views |
Last post | ||
|---|---|---|---|---|
|
|
Virgin 17059553
Started by Pav8427 |
10 Replies
5099 Views |
March 27, 2020, 02:18:18 AMby Cliff Ruggles |
|
|
|
camshaft rules of thumb?
Started by Marx3 |
10 Replies
7003 Views |
July 12, 2013, 04:05:46 PM by Shark Racer |
|
|
|
Do i need a bigger needle and seat???
Started by Mr.Pontiac |
10 Replies
4376 Views |
September 23, 2018, 07:43:58 PM by 77cruiser |
|
|
|
E10/15 fuel and vapor lock.
Started by old blue 75 |
10 Replies
6135 Views |
June 25, 2020, 09:24:19 PM by blazer74 |
|
|
|
One of those @#%!#%^ days
Started by Shark Racer |
10 Replies
7194 Views |
May 24, 2013, 03:25:13 PM by Ethan1 |
|
|
|
Largest N/S you've used?
Started by 77cruiser |
10 Replies
5156 Views |
September 09, 2017, 05:54:28 AM by Cliff Ruggles |
|
|
|
Quadrajet for 283
Started by Haagdakta |
10 Replies
7566 Views |
March 19, 2017, 02:46:26 PM by markedmondson |
|
|
|
Main Well Bleed Tubes
Started by von |
10 Replies
9915 Views |
December 07, 2010, 08:00:45 PM by kelley555 |
|
|
|
Lean condition at idle only
Started by jberenyi |
10 Replies
4596 Views |
April 21, 2022, 09:41:32 AM by Cliff Ruggles |
|
|
|
What Spacer
Started by 71stagegs |
10 Replies
7270 Views |
March 12, 2013, 07:17:33 AM by 71stagegs |
|
|
|
B stamped primary rods
Started by mcx |
10 Replies
4458 Views |
February 16, 2020, 02:17:50 AM by mcx |
|
|
|
Ford 429 CJ Quadrajet
Started by Cliff Ruggles |
10 Replies
9117 Views |
March 22, 2024, 01:41:01 AM by Cliff Ruggles |
|
|
9 Replies
6627 Views |
May 03, 2024, 06:13:47 AM by Cliff Ruggles |
|
|
|
|
9 Replies
6975 Views |
July 31, 2012, 03:16:19 AM by Cliff Ruggles |
|
|
|
|
Upper Idle Air Bleeds
Started by jagness |
9 Replies
7741 Views |
June 26, 2020, 09:00:46 PM by jagness |
|
|
|
Stripped fuel inlet
Started by Jeffs68 |
9 Replies
5830 Views |
May 19, 2016, 03:01:58 AM by Cliff Ruggles |
|
|
|
Need help with setup of working Q jet
Started by raguza123 |
9 Replies
5836 Views |
June 28, 2013, 02:15:27 PM by raguza123 |
|
|
|
Advice building carb
Started by CultClassik |
9 Replies
6658 Views |
December 18, 2014, 05:33:28 AM by Cliff Ruggles |
|
|
|
Base setting for throttle angle
Started by Pav8427 |
9 Replies
4298 Views |
March 05, 2018, 04:33:58 PM by Frank400 |
|
|
|
Removing Idle Tubes
Started by brown7373 |
9 Replies
9733 Views |
November 23, 2014, 05:59:13 PM by Bigal442 |
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll