News:
We buy American, and use American Made parts for all of our exclusive Cliff's Carburetor parts and kits.
| Subject / Started by | Replies / Views | Last post  |
||
|---|---|---|---|---|
|
|
What Float Height for 7029240?
Started by Shiny |
1 Replies
3319 Views |
April 03, 2009, 06:07:24 AMby Cliff Ruggles |
|
|
|
fuel pressure
Started by brock20 |
1 Replies
3399 Views |
April 02, 2009, 03:08:27 PM by Schurkey |
|
|
|
Secondary Brass Tubes on QJet
Started by bnorris_74 |
4 Replies
4177 Views |
March 28, 2009, 10:49:13 AM by bnorris_74 |
|
|
|
secondarys not opening
Started by Heath |
5 Replies
5380 Views |
March 24, 2009, 05:09:01 AM by Cliff Ruggles |
|
|
17 Replies
9467 Views |
February 26, 2009, 08:35:12 AM by Cliff Ruggles |
|
|
|
|
12 Replies
25426 Views |
February 25, 2009, 06:28:36 AM by Cliff Ruggles |
|
|
|
|
Conversion of a Q-Jet
Started by bigvette1 |
1 Replies
4003 Views |
February 23, 2009, 04:52:17 AM by Cliff Ruggles |
|
|
|
Engine dies on intitial cold start
Started by liberty |
3 Replies
4335 Views |
February 09, 2009, 04:54:21 AM by Cliff Ruggles |
|
|
idle restictions question
Started by Mr.Pontiac |
1 Replies
3880 Views |
February 09, 2009, 04:51:42 AM by Cliff Ruggles |
|
|
|
4 Replies
5357 Views |
January 24, 2009, 04:20:07 AM by Cliff Ruggles |
|
|
|
|
Diagnostic chart
Started by Hotrodrobert |
4 Replies
5388 Views |
January 20, 2009, 04:10:14 AM by Cliff Ruggles |
|
|
|
Where to start?
Started by JimC |
9 Replies
6478 Views |
December 30, 2008, 02:43:26 PM by JimC |
|
|
|
A GOOD ONE!!!
Started by motman |
7 Replies
5607 Views |
December 27, 2008, 05:56:56 PM by motman |
|
|
|
Rough idle after choke opens
Started by dblhh |
3 Replies
4831 Views |
November 30, 2008, 06:56:28 AM by Cliff Ruggles |
|
|
|
4 Replies
4276 Views |
November 19, 2008, 06:32:46 AM by Cliff Ruggles |
|
|
|
|
wot on start up after rebuild
Started by BOBBYBUICK |
2 Replies
3867 Views |
November 19, 2008, 06:30:36 AM by Cliff Ruggles |
|
|
|
Acceleration problems
Started by dn010 |
2 Replies
6835 Views |
November 08, 2008, 06:07:53 PM by dn010 |
|
|
|
17058263 carb
Started by 17058263 |
3 Replies
6528 Views |
October 21, 2008, 04:39:48 AM by Cliff Ruggles |
|
|
|
replacing bushings
Started by FORREST MILLER |
1 Replies
4007 Views |
October 21, 2008, 04:29:23 AM by Cliff Ruggles |
|
|
|
Which epoxy to use?
Started by Z28 Eric |
6 Replies
6583 Views |
September 30, 2008, 09:51:14 PM by FORREST MILLER |
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll