News:
We buy American, and use American Made parts for all of our exclusive Cliff's Carburetor parts and kits.
Subject  / Started by |
Replies / Views | Last post | ||
|---|---|---|---|---|
|
|
Un-warping jig
Started by Pav8427 |
6 Replies
2035 Views |
March 03, 2018, 03:11:41 AMby Pav8427 |
|
|
|
Unknown spring
Started by mcx |
5 Replies
1197 Views |
November 16, 2019, 03:27:53 PM by mcx |
|
|
|
Unmarked Metering Rods
Started by cobalt327 |
1 Replies
2472 Views |
March 19, 2011, 05:19:07 AM by Cliff Ruggles |
|
|
|
Unusual Secondary Jet Repair
Started by levyb |
1 Replies
1560 Views |
May 29, 2012, 04:17:04 AM by Cliff Ruggles |
|
|
|
unwarping tool finished and tested.
Started by omaha |
7 Replies
4287 Views |
March 24, 2016, 02:43:42 AM by Cliff Ruggles |
|
|
|
1 Replies
1423 Views |
October 04, 2017, 05:12:09 AM by Cliff Ruggles |
|
|
|
|
1 Replies
1451 Views |
October 04, 2017, 05:12:51 AM by Cliff Ruggles |
|
|
|
|
upper air bleeds or idle down channel
Started by Stripes |
1 Replies
989 Views |
April 10, 2019, 02:56:53 PM by mcx |
|
|
|
Upper Idle Air Bleeds
Started by jagness |
9 Replies
3107 Views |
June 26, 2020, 09:00:46 PM by jagness |
|
|
|
Use little clip on end of needle?
Started by daveo76 |
1 Replies
1715 Views |
May 19, 2012, 11:21:34 PM by daveo76 |
|
|
|
using 17084222 on 68 396 325 hp
Started by bruno |
5 Replies
2314 Views |
October 25, 2015, 09:10:32 PM by bruno |
|
|
|
3 Replies
1518 Views |
October 30, 2018, 02:05:35 AM by Cliff Ruggles |
|
|
|
|
Using the green power piston spring
Started by stevef |
0 Replies
919 Views |
October 16, 2022, 04:59:39 PM by stevef |
|
|
|
using the new idle mixture screws
Started by stevef |
2 Replies
952 Views |
October 25, 2022, 07:43:51 PM by stevef |
|
|
31 Replies
8048 Views |
June 06, 2018, 04:24:44 AM by Cliff Ruggles |
|
|
|
|
vacuum break control
Started by Vics63 |
8 Replies
2540 Views |
June 01, 2020, 03:23:04 AM by Cliff Ruggles |
|
|
|
Vacuum caps
Started by Huddie |
1 Replies
1849 Views |
September 19, 2010, 05:01:22 PM by clutch442 |
|
|
|
4 Replies
4797 Views |
May 23, 2017, 02:22:51 PM by jamesF |
|
|
|
|
vacuumlevel with Crower 60240
Started by Marx3 |
7 Replies
3889 Views |
January 25, 2015, 07:22:48 AM by Marx3 |
|
|
|
velocity stacks
Started by dlong70elcamino |
7 Replies
3509 Views |
August 31, 2017, 03:10:57 AM by Cliff Ruggles |
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll