News:
We buy American, and use American Made parts for all of our exclusive Cliff's Carburetor parts and kits.
Subject  / Started by |
Replies / Views | Last post | ||
|---|---|---|---|---|
|
|
Rear air door opening vs CFM
Started by 70GS455 |
13 Replies
3101 Views |
December 27, 2023, 06:54:34 PMby Cliff Ruggles |
|
|
33 Replies
10781 Views |
April 13, 2016, 03:17:40 AM by Cliff Ruggles |
|
|
|
3 Replies
1732 Views |
April 01, 2020, 02:06:34 AM by Cliff Ruggles |
|
|
|
|
Re Tapping idle mix holes
Started by 77cruiser |
1 Replies
1882 Views |
July 25, 2015, 01:30:16 PM by Ethan1 |
|
|
|
1 Replies
1634 Views |
October 14, 2018, 01:34:13 AM by Cliff Ruggles |
|
|
|
|
Random 7041264 rebuild questions
Started by dataway |
5 Replies
2059 Views |
April 24, 2018, 02:08:16 AM by Cliff Ruggles |
|
|
|
11 Replies
5795 Views |
December 13, 2013, 06:23:45 AM by motorvation2go |
|
|
|
|
1 Replies
1871 Views |
February 24, 2013, 05:16:12 AM by Cliff Ruggles |
|
|
|
|
Quick quiz on plating parts.
Started by Pav8427 |
1 Replies
1356 Views |
December 15, 2022, 05:45:01 AM by Cliff Ruggles |
|
|
|
3 Replies
1807 Views |
November 26, 2021, 07:13:15 AM by Cliff Ruggles |
|
|
|
|
Question on needle and seat size
Started by Frank400 |
2 Replies
1870 Views |
September 10, 2015, 06:14:37 PM by Frank400 |
|
|
|
Question on California carb
Started by TimT |
1 Replies
3240 Views |
March 13, 2009, 05:07:57 AM by Cliff Ruggles |
|
|
|
question on 17046240 upper air bleeds
Started by Mr.Pontiac |
0 Replies
3213 Views |
November 05, 2009, 12:18:38 PM by Mr.Pontiac |
|
|
|
Question for cliff on idle bypass air
Started by renegade14 |
1 Replies
2678 Views |
July 02, 2011, 04:39:17 AM by Cliff Ruggles |
|
|
|
1 Replies
2523 Views |
December 06, 2011, 03:23:16 AM by Cliff Ruggles |
|
|
|
|
Question about resizing main bleeds
Started by 73 Z28 |
2 Replies
3492 Views |
April 28, 2009, 05:20:55 AM by Cliff Ruggles |
|
|
|
6 Replies
3301 Views |
April 12, 2014, 10:05:37 AM by 429bbf |
|
|
|
|
11 Replies
3847 Views |
November 23, 2018, 07:23:48 AM by LouC |
|
|
|
|
Quesiton on Drilling Idle Tubes
Started by WideTrack |
2 Replies
2122 Views |
May 13, 2020, 07:53:04 PM by WideTrack |
|
|
|
1 Replies
4634 Views |
August 24, 2012, 05:02:29 AM by Cliff Ruggles |
|
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll