News:
Need a Budget Carb Rebuild Kit? Check out our $45.95 SR Kits. Same Top Quality Parts as the Full Kits.
Subject  / Started by |
Replies / Views | Last post | ||
|---|---|---|---|---|
|
|
Fast Idle adjustment question?
Started by Overcamber |
5 Replies
3605 Views |
April 20, 2016, 07:33:50 AMby Overcamber |
|
|
|
Excessive Fuel Burn Black Exhaust
Started by trudaddy |
3 Replies
5701 Views |
September 04, 2025, 01:04:28 AM by Cliff Ruggles |
|
|
|
electric choke
Started by Paul |
9 Replies
6510 Views |
June 15, 2013, 10:51:43 AM by Schurkey |
|
|
|
Effect of Fuel Pressure
Started by Brian B. |
8 Replies
5354 Views |
September 10, 2020, 04:53:40 AM by Cliff Ruggles |
|
|
|
Edelbrock1910 lean idle
Started by matt69olds |
3 Replies
3362 Views |
December 19, 2015, 01:48:14 AM by Cliff Ruggles |
|
|
|
7 Replies
2925 Views |
August 02, 2025, 08:06:47 AM by Cliff Ruggles |
|
|
|
|
Edelbrock 1910 850 tuning
Started by matt69olds |
8 Replies
8846 Views |
September 05, 2013, 04:22:26 AM by Cliff Ruggles |
|
|
17 Replies
9615 Views |
October 10, 2019, 02:28:32 AM by Cliff Ruggles |
|
|
|
|
Edelbrock 1901 drip
Started by deric83616 |
1 Replies
3311 Views |
April 30, 2012, 02:38:57 AM by Cliff Ruggles |
|
|
|
Edelbrock 1901 and 454 BBC
Started by deric83616 |
3 Replies
6466 Views |
December 23, 2009, 04:24:50 AM by Cliff Ruggles |
|
|
|
Eccentric cam?
Started by arrowem |
1 Replies
3435 Views |
August 01, 2010, 09:32:24 PM by arrowem |
|
|
|
E4ME on 81 Corvette...2 Questions
Started by HammerDown |
2 Replies
5792 Views |
August 21, 2011, 09:07:53 AM by HammerDown |
|
|
|
E4ME
Started by Ray C. Merrill |
1 Replies
3686 Views |
September 27, 2012, 03:54:49 AM by Cliff Ruggles |
|
|
|
E-brock 1902 modifications
Started by CJK440 |
5 Replies
3821 Views |
April 09, 2018, 05:06:41 AM by Cliff Ruggles |
|
|
|
Drilling idle tubes?
Started by arrowem |
1 Replies
4292 Views |
July 31, 2010, 07:10:49 PM by arrowem |
|
|
|
Drilling idle mixture screw opening
Started by Jeff1 |
5 Replies
4783 Views |
January 17, 2016, 09:21:04 PM by blazer74 |
|
|
|
Drilling a hole for ported vacuum advance
Started by J.Peter |
2 Replies
7092 Views |
August 04, 2024, 03:18:23 PM by J.Peter |
|
|
|
Drill Throttle Plates?
Started by von |
5 Replies
7690 Views |
February 09, 2010, 06:16:32 PM by Cliff Ruggles |
|
|
30 Replies
18284 Views |
December 22, 2022, 03:44:46 AM by Cliff Ruggles |
|
|
|
|
4 Replies
3457 Views |
November 27, 2019, 08:18:04 AM by Mr.Pontiac |
|
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll