News:
Need a Budget Carb Rebuild Kit? Check out our $45.95 SR Kits. Same Top Quality Parts as the Full Kits.
| Subject / Started by | Replies  / Views |
Last post | ||
|---|---|---|---|---|
|
|
1 Replies
1881 Views |
February 20, 2012, 04:03:05 AMby Cliff Ruggles |
|
|
|
|
1 Replies
1636 Views |
May 25, 2012, 04:29:27 AM by Cliff Ruggles |
|
|
|
|
Can the EGR port be used for dist vacuum?
Started by gkz |
1 Replies
1600 Views |
May 25, 2012, 04:28:16 AM by Cliff Ruggles |
|
|
|
PCV to the REAR, OK?
Started by garybohannon |
1 Replies
2265 Views |
April 17, 2011, 11:24:27 AM by Schurkey |
|
|
|
Use little clip on end of needle?
Started by daveo76 |
1 Replies
1718 Views |
May 19, 2012, 11:21:34 PM by daveo76 |
|
|
|
STAGGERED JETTING
Started by qjetsrule |
1 Replies
2133 Views |
May 17, 2012, 03:27:28 PM by TommyK |
|
|
|
1 Replies
2204 Views |
December 06, 2010, 06:49:45 PM by Cliff Ruggles |
|
|
|
|
1 Replies
1727 Views |
May 08, 2012, 04:19:42 AM by Cliff Ruggles |
|
|
|
|
1 Replies
1836 Views |
April 12, 2011, 04:03:33 AM by Cliff Ruggles |
|
|
|
|
1 Replies
2223 Views |
May 26, 2011, 07:15:39 AM by Cliff Ruggles |
|
|
|
|
1 Replies
2152 Views |
August 26, 2010, 03:29:18 AM by Cliff Ruggles |
|
|
|
|
Fuel ratio & float level
Started by 77cruiser |
1 Replies
2189 Views |
May 13, 2010, 05:15:03 AM by Cliff Ruggles |
|
|
|
ULTRASONIC CLEANERS
Started by billy 2 |
1 Replies
2331 Views |
May 09, 2010, 03:58:09 AM by Cliff Ruggles |
|
|
|
Removing Primary Shaft Screws
Started by von |
1 Replies
2100 Views |
May 08, 2010, 05:05:19 AM by billy 2 |
|
|
|
Is clip mandatory on needle ?
Started by Frank400 |
1 Replies
2090 Views |
May 04, 2012, 04:14:23 AM by Cliff Ruggles |
|
|
|
17058213 Carb on '68 Pontiac 350 HO?
Started by crossbuck4 |
1 Replies
2213 Views |
April 06, 2012, 06:32:24 AM by Cliff Ruggles |
|
|
|
Just wanted to share...
Started by Marx3 |
1 Replies
2207 Views |
April 24, 2010, 12:53:05 PM by Cliff Ruggles |
|
|
|
1 Replies
2243 Views |
April 22, 2010, 04:51:07 AM by Cliff Ruggles |
|
|
|
|
Too Large Idle Channel Restriction?
Started by von |
1 Replies
2896 Views |
April 22, 2010, 04:47:27 AM by Cliff Ruggles |
|
|
|
idle tubes
Started by 73ss |
1 Replies
1828 Views |
March 31, 2012, 04:16:14 AM by Cliff Ruggles |
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll