News:
Need a Budget Carb Rebuild Kit? Check out our $45.95 SR Kits. Same Top Quality Parts as the Full Kits.
| Subject / Started by | Replies  / Views |
Last post | ||
|---|---|---|---|---|
|
|
Rear choke pull off
Started by Haagdakta |
2 Replies
2923 Views |
January 25, 2017, 08:02:31 AMby Haagdakta |
|
|
|
Power mods
Started by ShadowElky |
2 Replies
3240 Views |
November 06, 2012, 09:33:22 PM by ShadowElky |
|
|
|
Bent my primary metering rod arm
Started by Dark T/A |
2 Replies
3075 Views |
October 15, 2012, 07:56:58 AM by Dark T/A |
|
|
|
I rebuilt my carb and it runs very rich
Started by Aprules2 |
2 Replies
2857 Views |
May 15, 2014, 11:02:41 PM by qjetsrule |
|
|
|
Sticky secondaries
Started by gtome |
2 Replies
2777 Views |
September 17, 2012, 05:11:44 AM by Cliff Ruggles |
|
|
|
Can these idle tubes be re used?
Started by Kjetil |
2 Replies
2904 Views |
September 15, 2012, 06:26:30 AM by Kjetil |
|
|
|
2bbl carter on 81 jeep
Started by jbh7052 |
2 Replies
2602 Views |
August 24, 2016, 01:12:23 PM by jbh7052 |
|
|
|
2 Replies
2825 Views |
March 20, 2017, 10:14:40 AM by Ethan1 |
|
|
|
|
Idle Bypass Air Question
Started by Time Machines |
2 Replies
2939 Views |
August 29, 2012, 06:02:32 PM by Time Machines |
|
|
|
hot idle compensator
Started by tom t |
2 Replies
4057 Views |
July 30, 2016, 03:48:14 PM by tom t |
|
|
|
Hollow Carb Studs
Started by jamesF |
2 Replies
5434 Views |
July 17, 2017, 03:01:27 PM by jamesF |
|
|
|
Carb dumping Too Much Fuel
Started by cutlassrichard |
2 Replies
3784 Views |
April 15, 2011, 11:10:30 AM by cutlassrichard |
|
|
|
stuck power piston
Started by j_oetjens |
2 Replies
4141 Views |
June 03, 2014, 02:44:49 PM by j_oetjens |
|
|
|
float level and consequences question
Started by Frank400 |
2 Replies
2984 Views |
June 12, 2014, 04:56:20 AM by Cliff Ruggles |
|
|
|
2 Replies
4902 Views |
April 24, 2017, 05:40:16 PM by Frank400 |
|
|
|
|
Determining CFM by the Carb Number
Started by pggto |
2 Replies
3515 Views |
March 30, 2011, 09:39:17 AM by Schurkey |
|
|
|
Secondary Opening?
Started by JMac11 |
2 Replies
3196 Views |
March 29, 2011, 03:21:09 AM by Cliff Ruggles |
|
|
|
will q/jet work on my eng.?
Started by bober |
2 Replies
3239 Views |
October 09, 2013, 05:49:25 AM by bober |
|
|
|
Removing Loctited Screws
Started by von |
2 Replies
3593 Views |
March 27, 2011, 05:27:57 AM by von |
|
|
|
Carb setup help
Started by Clutch |
2 Replies
3266 Views |
March 18, 2011, 05:43:17 AM by Cliff Ruggles |
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll