News:
We buy American, and use American Made parts for all of our exclusive Cliff's Carburetor parts and kits.
Subject / Started by  |
Replies / Views | Last post | ||
|---|---|---|---|---|
|
|
australian factory manual choke
Started by daveqjet |
8 Replies
6217 Views |
January 23, 2016, 03:36:43 AMby daveqjet |
|
|
|
Thanks, Cliff!
Started by daveo76 |
1 Replies
2899 Views |
August 26, 2012, 04:34:58 PM by Cliff Ruggles |
|
|
|
Use little clip on end of needle?
Started by daveo76 |
1 Replies
3090 Views |
May 19, 2012, 11:21:34 PM by daveo76 |
|
|
|
Primary throttle shaft allowable play?
Started by daveo76 |
8 Replies
10801 Views |
April 13, 2012, 11:35:31 PM by daveo76 |
|
|
|
Quadrajet idle mixture screw cap removal
Started by davel |
9 Replies
8313 Views |
November 13, 2019, 08:29:19 PM by 429bbf |
|
|
|
5 Replies
4725 Views |
April 01, 2019, 02:02:45 AM by Cliff Ruggles |
|
|
|
|
Plug in air horn directly over APT
Started by Dave57 |
5 Replies
3345 Views |
August 04, 2019, 01:15:02 AM by Cliff Ruggles |
|
|
|
Spread- to square-bore adapters?
Started by dave |
3 Replies
12767 Views |
January 16, 2009, 06:04:45 AM by Cliff Ruggles |
|
|
|
3 Replies
3133 Views |
October 30, 2018, 02:05:35 AM by Cliff Ruggles |
|
|
|
|
7041264 for use on a 68 GTO
Started by dataway |
2 Replies
3433 Views |
November 10, 2017, 12:45:25 AM by dataway |
|
|
|
Random 7041264 rebuild questions
Started by dataway |
5 Replies
3440 Views |
April 24, 2018, 02:08:16 AM by Cliff Ruggles |
|
|
|
Bent my primary metering rod arm
Started by Dark T/A |
2 Replies
3407 Views |
October 15, 2012, 07:56:58 AM by Dark T/A |
|
|
|
3 Replies
3520 Views |
October 02, 2012, 10:03:11 PM by Zac Agee |
|
|
|
|
0 Replies
2317 Views |
August 24, 2022, 04:43:21 AM by DamienSib |
|
|
|
|
17054932 3242
Started by d.j.welch |
6 Replies
5804 Views |
November 16, 2012, 05:34:38 AM by d.j.welch |
|
|
|
secondary hanger and gasket thickness
Started by D Denzin |
3 Replies
3470 Views |
June 30, 2014, 05:36:46 AM by Cliff Ruggles |
|
|
|
Idle down channel replacement
Started by cyclops1032 |
1 Replies
3996 Views |
March 20, 2011, 02:05:11 AM by omaha |
|
|
|
Cracked Base Plate
Started by cutlassrichard |
1 Replies
3262 Views |
April 19, 2011, 04:44:26 AM by Cliff Ruggles |
|
|
|
Carb dumping Too Much Fuel
Started by cutlassrichard |
2 Replies
4161 Views |
April 15, 2011, 11:10:30 AM by cutlassrichard |
|
|
|
Advice building carb
Started by CultClassik |
9 Replies
6848 Views |
December 18, 2014, 05:33:28 AM by Cliff Ruggles |
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll