News:
We buy American, and use American Made parts for all of our exclusive Cliff's Carburetor parts and kits.
| Subject / Started by | Replies  / Views |
Last post | ||
|---|---|---|---|---|
|
|
Quadrajet 4MV 1968 Camaro
Started by CaliChevyV8 |
1 Replies
2836 Views |
December 03, 2011, 07:30:58 AMby Cliff Ruggles |
|
|
|
17056281 800 cfm, good find ?
Started by Frank400 |
1 Replies
3110 Views |
October 16, 2011, 05:58:50 PM by Cliff Ruggles |
|
|
|
1 Replies
2903 Views |
August 26, 2010, 03:29:18 AM by Cliff Ruggles |
|
|
|
|
linkage and spring
Started by petes70 |
1 Replies
2610 Views |
February 22, 2011, 03:36:06 AM by Cliff Ruggles |
|
|
|
Fuel ratio & float level
Started by 77cruiser |
1 Replies
2960 Views |
May 13, 2010, 05:15:03 AM by Cliff Ruggles |
|
|
|
ULTRASONIC CLEANERS
Started by billy 2 |
1 Replies
3089 Views |
May 09, 2010, 03:58:09 AM by Cliff Ruggles |
|
|
|
Removing Primary Shaft Screws
Started by von |
1 Replies
2843 Views |
May 08, 2010, 05:05:19 AM by billy 2 |
|
|
|
Tube bulge
Started by Enigmatic1 |
1 Replies
2886 Views |
July 15, 2011, 02:01:35 AM by omaha |
|
|
|
Just wanted to share...
Started by Marx3 |
1 Replies
3001 Views |
April 24, 2010, 12:53:05 PM by Cliff Ruggles |
|
|
|
down channel restriction
Started by firebird*boz |
1 Replies
2802 Views |
June 28, 2011, 03:04:27 AM by Cliff Ruggles |
|
|
|
1 Replies
2992 Views |
April 22, 2010, 04:51:07 AM by Cliff Ruggles |
|
|
|
|
Too Large Idle Channel Restriction?
Started by von |
1 Replies
3683 Views |
April 22, 2010, 04:47:27 AM by Cliff Ruggles |
|
|
|
The big helicoil taps. (1 x 20).
Started by omaha |
1 Replies
2693 Views |
June 21, 2011, 04:11:03 AM by Cliff Ruggles |
|
|
|
secondary fuel nozzle question
Started by Mr.Pontiac |
1 Replies
2539 Views |
June 26, 2011, 05:14:34 AM by Cliff Ruggles |
|
|
|
APT Adjust '75 Olds Carb
Started by von |
1 Replies
2854 Views |
June 16, 2011, 03:37:48 AM by Cliff Ruggles |
|
|
|
1 Replies
2849 Views |
January 28, 2011, 04:40:44 AM by Cliff Ruggles |
|
|
|
|
Gas in Vac Port
Started by JMac11 |
1 Replies
2536 Views |
November 04, 2011, 05:40:49 AM by Cliff Ruggles |
|
|
|
Original factory jets and rods
Started by mwoolston |
1 Replies
2864 Views |
January 15, 2012, 04:33:52 AM by Cliff Ruggles |
|
|
|
base plate locating pins
Started by firebird*boz |
1 Replies
2642 Views |
June 12, 2011, 03:00:04 AM by Cliff Ruggles |
|
|
|
Best Carb Cleaner
Started by Mark R |
1 Replies
3387 Views |
December 09, 2009, 04:32:07 AM by Cliff Ruggles |
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll