News:
Buy "The Book" on Q-jets and OverDrive Transmission Swaps. On the Website Home Page!
Subject / Started by  |
Replies / Views | Last post | ||
|---|---|---|---|---|
|
|
th350 clutch pistons air check video
Started by stevef |
6 Replies
3520 Views |
November 01, 2018, 06:29:48 AMby stevef |
|
|
|
th350 piston springs
Started by stevef |
3 Replies
3414 Views |
December 23, 2024, 01:52:39 AM by Cliff Ruggles |
|
|
|
Leftovers from rebuild kit
Started by stevef |
5 Replies
6736 Views |
February 20, 2010, 06:18:22 AM by stevef |
|
|
|
th350 rebuild quick question
Started by stevef |
3 Replies
4034 Views |
November 29, 2024, 02:41:02 PM by stevef |
|
|
|
using the new idle mixture screws
Started by stevef |
2 Replies
2530 Views |
October 25, 2022, 07:43:51 PM by stevef |
|
|
|
5 Replies
3195 Views |
August 19, 2022, 12:39:07 PM by stevef |
|
|
|
th350 question
Started by stevef |
11 Replies
5140 Views |
September 16, 2018, 09:49:09 AM by stevef |
|
|
|
4 Replies
7496 Views |
July 30, 2011, 05:23:00 AM by stevef |
|
|
|
|
screw in the bottom of pump well?
Started by stevef |
1 Replies
2656 Views |
April 26, 2014, 02:58:53 PM by stevef |
|
|
|
Pulling idle tubes
Started by stevef |
6 Replies
4210 Views |
April 30, 2014, 08:48:41 PM by qjetsrule |
|
|
|
16 Replies
9465 Views |
March 18, 2019, 10:57:39 AM by stevef |
|
|
|
|
fuel needle seat
Started by stevef |
2 Replies
4016 Views |
April 18, 2016, 06:13:05 PM by stevef |
|
|
|
7029241 Buick carb
Started by srb12 |
13 Replies
5173 Views |
October 30, 2022, 02:27:25 AM by Cliff Ruggles |
|
|
|
Can the Qjet be used as a blow through carb?
Started by SRB |
6 Replies
10809 Views |
February 15, 2010, 09:16:57 AM by 77cruiser |
|
|
|
3 Replies
3395 Views |
December 27, 2015, 09:01:12 AM by markedmondson |
|
|
|
|
Quadrajet rear vent
Started by Spudboy |
3 Replies
5131 Views |
December 22, 2009, 09:42:59 AM by Spudboy |
|
|
|
Removing the q-jet choke housing.
Started by Spudboy |
1 Replies
2987 Views |
December 25, 2015, 03:45:54 AM by Cliff Ruggles |
|
|
|
Duplicating the teflon green plating.
Started by Spudboy |
5 Replies
4273 Views |
June 12, 2016, 05:24:43 PM by Ethan1 |
|
|
|
Winter rebuilds
Started by Spudboy |
2 Replies
5552 Views |
July 23, 2014, 11:30:00 PM by 69abody |
|
|
|
Rusty vacuum ports
Started by Spudboy |
0 Replies
3991 Views |
June 12, 2010, 12:48:07 PM by Spudboy |
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 20 replies)
Locked Topic
Sticky Topic
Poll